If you continue to experience problems, please contact Focusrite Technical Support. To turn the outputs grey in MixControl, simply hold down the SHIFT key on your keyboard while clicking on them. However please exercise caution as any signal coming out of the corresponding line outputs will be very loud. Routing flexibility and intuitive one-click set-up solutions Saffire MixControl provides an 16 x 8 DSP mixer with excellent output routing and monitoring. Grey outputs will output audio at full volume, and so having the headphone outputs set to Grey will mean that utilising just the headphone output level control should give sufficient level to the headphones.If using the headphone outputs set to Blue, ensure that the monitor level is nice and high. It is possible to have the headphone outputs set to ‘Blue’, yet still not hear audio as there isn’t sufficient level. Blue outputs will pass audio, but the level of the output is dependent on the position of the monitor level control.For audio to be heard from the headphone outputs, the corresponding line outputs must not be set to Red. Red outputs are muted and won’t pass any audio.This is done in the Monitor section of Saffire MixControl, shown below.Īs demonstrated by the image above, the monitor outputs have three states, signified by three different colours, Red, Blue, and Grey. It is then necessary to ensure that sufficient level is being sent out of the headphone outputs to the headphones. This panel can be found in the bottom left-hand corner of Saffire MixControl. It is worth noting that most computer audio software will send audio out of DAW 1 (Left Channel) and DAW 2 (Right Channel) by default. Select from the choice of Inputs, DAW (computer) Outputs, and Mixes by clicking in the box next to the relevant output, and route audio to the headphones. In the example above (of a Saffire Pro 24 DSP), Headphone Output 1 (on the Saffire hardware) is a copy of Line Outputs 3&4, and Headphone Output 2 (on the Saffire hardware) is a copy of Line Outputs 5&6. These outputs are marked by the headphone symbol ( ) in the routing section of Saffire MixControl, as shown below. Focusrite product compatibility with macOS 13 'Ventura' on Intel-based systems. Focusrite product compatibility with macOS 13 'Ventura' on Apple Silicon-based systems. How to live stream and video call with your Focusrite interface. How to install Focusrite drivers on Windows. Mix control is that a necessary item for your DAW to function.Ĭomplete kontrol, maybe disable that one till you have your basic system functions working.The headphone outputs from Saffire MixControl are copies of specific line outputs on the rear of the interface, so it is important to ensure that you’re routing audio to the correct outputs. Optimising your PC for Audio on Windows 10. Have you checked your reaper settings for correct setting, don't forget about looking at your routing. If you are seeing activity on the tracks and the msster I would look at items that are not part of your basic configuration. What I don't get is that the sample rate was always set to 44.1 and I never had any problems.ġ11GB ATA Samsung ssd 840 (app and system) If I set the sample rate to 44.1, no sound. Moreover, when I listen to mp3, wav or flac files with VLC or Foobar, the sample rate is set to 48 on my audio interface. But if I set it on 48 and switch off/on, I can hear the output sound. If I switch my Saffire Pro 24 off with the sample rate set on 44.1, I still get no output sound when I switch it on. It seemed that everything was back to normal. Yesterday, I've decided to uninstall/re-install MixControl. This worked fine but was not good enough for me knowing that I didn't have any sync problems before that. I could see signal going out on MixControl but still no sound on my headphones or monitors.Īfter searching the net, I found out a solution: change the sync source on MixControl from internal to SPDIF (for instance) and then switch it back to internal. I kept on working, played a bit on Steam and shuted down my computer.Ī few hours later, I turned my pc on and started a new session in Reaper but no sound came out on my monitors. The other day, I was working on Reaper when I tried to watch a Youtube video on my second screen but no sound came out of it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |